C4 Vette Valve Cover Gasket Replacement Part VI - Corvette Forum
 
LinkBack Thread Tools Display Modes
post #1 of 1 (permalink) Old 04-10-2010, 09:55 PM Thread Starter
Junior Member
 
Join Date: Dec 2009
Location: Az
Posts: 3
C4 Vette Valve Cover Gasket Replacement Part VI

For the pics and vids you'll have to nav over to my blog

http://timsweet.wordpress.com/2010/0...ement-part-vi/

Ok..let me finish up blogging to you on this event. I had a read ask if it has really taken this long and the answer is No and Yes. (I’ll explain the YES in a bit..it ain’t pretty!!!!)

After find the correct bolts, wrestling the covers back into place was, I bolted them down. Installed they looked pretty good.

Check it out.


Left side painted and installed. Still missing the emblem..right now



The only difficulty was aligning the holes in the cover and the gasket and the engine. Due to the lack of room to maneuver I wasn’t able to keep the gasket and cover holes aligned while wrestling them into place. I used two (small enough to slide into the threaded holes without damaging) phillips head screw driver to help keep them aligned and put the bolts in.

Errrkk……whatever you do tighten them carefully…..let me spell that for you (Mickey Mouse Club tune playing in my head) C…A….R.(because you care about your car)…E…F….U…L…L…(cause you want to keep the oil full)…..Y…(because if you tighten too much on the 1984 C4 magnesium valve covers you’ll crack them and they can’t be welded, JB or other wise, and then you’ve got to find used ones, because aftermarket aren’t all that great)….Ok…end of Mickey Mouse Club song…and the end of one of the original valve covers….

And in case you didn’t get the between the lines intention of the above Errrkkkk…I broken one.

I wasn’t sure at first, my mind refused to process the sound so that I could be sure..it might have been a crack, or maybe I just crunched one of the plastic tubes covering a bundle of wires. Yeah..that’s it…I sure (it might have been a crack though….crap!!…let me spell that for you…oh…never mind….just invision huge font type all in upper case, bolded and underlined.)

I inspected the cover while it was in place and I couldn’t see anything and said…ok.average guy.. with average skills and average budget..you have above average luck…at least today…at least that’s what I thought…or hoped.

When that happens the only way to tell is to either take the cover back off and inspected…that wasn’t going to happen…or let her run and build up the oil pressure and see what happens….that is what you’d normally do any way after replace the gaskets.

Here she is running: (includes bonus views of the injectors…I think they are pretty cool to watch.)

<embed width=”600″ height=”361″ type=”application/x-shockwave-flash” allowFullscreen=”true” allowNetworking=”all” wmode=”transparent” src=”http://static.photobucket.com/player.swf?file=http://vid299.photobucket.com/albums/mm296/timsweet2200/MVI_6967.flv“>

http://s299.photobucket.com/albums/m...t=MVI_6967.flv

Covers don’t look to bad…but they aren’t going to stay…because..there really was a crack…but it didn’t show up by leaking on this run…it should up the next day when I took the car to work. I checked it when I arrived (about a 15 minute drive) no leaking…drove it home and she started to run poorly and had no power…yeah….it was leaking…on to a spark splug….got home and a little puddle of oil formed under the car and…well lets just say as I replaced the tightening episode in my head the crunching noise…sounded a lot more like a crack..in fact it was very clear on the replay!!!! The little referee in my head….said ‘After reviewing the play..the ruling in the garage is over turned, and Tim is charged a time out and $400.00 fine for cracking the cover and the vette gets parked until the parts get here!’

Here is the pick where the crack occurred.


Yup...cracked!!!!



That was Monday (4/5/2010) fast forward to today new cover have arrived (chrome) and they’ll be installed today or tomorrow. So Yes it was finished and now No it’s not.

Thanks for reading.

Tim

Tim Sweet
Tucson, Az
Blogging @ timsweet.wordpress.com

5.7 Liter 350 Crossfire Injection RPO L83, BUILT LEVEL 2 - 4 speed Automatic Overdrive Trans, limited slip real axle, Chromed Original Aluminum Wheels, RPO Z51 Performance Handling Package, All digital dash, Power everything, Delco_Bose stereo
timsweet is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Corvette Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome